Sabtu, 30 Oktober 2010
smadav 8.3
Jumat, 29 Oktober 2010
unik air zam-zam
Kandungan mineral
———————————–
Tidak seperti air mineral yang umum dijumpai, air Zamzam in memang unik mengandung elemen-elemen alamiah sebesar 2000 mg perliter. Biasanya air mineral alamiah (hard carbonated water) tidak akan lebih dari 260 mg per liter. Elemen-elemen kimiawi yang terkandung dalam air Zamzam dapat dikelompokkan menjadi
Yang pertama, positive ions seperti misal sodium (250 mg per litre), calcium (200 mg per litre), potassium (20 mg per litre), dan magnesium (50 mg per litre).
Kedua, negative ions misalnya sulphur (372 mg per litre), bicarbonates (366 mg per litre), nitrat (273 mg per litre), phosphat (0.25 mg per litre) and ammonia (6 mg per litre).
Molekul air zam zam
Kandungan-kandungan elemen-elemen kimiawi inilah yang menjadikan rasa dari air Zamzam sangat khas dan dipercaya dapat memberikan khasiat khusus. Air yang sudah siap saji yang bertebaran disekitar Masjidil Haram dan Masjid Nabawi di Madinah merupakan air yang sudah diproses sehingga sangat aman dan segar diminum, ada yang sudah didinginkan dan ada yang sejuk (hangat). Namun konon prosesnya higienisasi ini tidak menggunakan proses kimiawi untuk menghindari perubahan rasa dan kandungan air ini.
http://moeltazam.wordpress.com
Minggu, 24 Oktober 2010
Why Do Clothes Wrinkle?
Water is the key culprit behind wrinkling of cellulose-based fabrics, such as cotton, linen, and rayon. The polymers in these fabrics are linked by hydrogen bonds, which are the same bonds that hold together molecules of water. Absorbent fabrics allow water molecules to penetrate the areas between the polymer chains, permitting the formation of new hydrogen bonds. The new shape becomes locked in as the water evaporates. Steam ironing works well on removing these wrinkles.
http://chemistry.about.com/od/howthingsworkfaqs/f/clotheswrinkle.htm
Sabtu, 09 Oktober 2010
Mengapa hukum Newton (Poyting dan Boys) mengabaikan Tekanan udara?
Hukum I Newton menyatakan bahwa :
Setiap benda tetap berada dalam keadaan diam atau bergerak dengan laju tetap sepanjang garis lurus, jika tidak ada gaya yang bekerja pada benda tersebut atau tidak ada gaya total pada benda tersebut.
Hukum II Newton tentang Gerak :
Jika suatu gaya total bekerja pada benda, maka benda akan mengalami percepatan, di mana arah percepatan sama dengan arah gaya total yang bekerja padanya. Vektor gaya total sama dengan massa benda dikalikan dengan percepatan benda.
Persamaan Hukum III Newton di atas juga bisa kita tulis sebagai berikut :
Faksi = -Freaksi
Hukum warisan Newton ini dikenal dengan julukan hukum aksi-reaksi. Ada aksi maka ada reaksi, yang besarnya sama dan berlawanan arah. Kadang-kadang kedua gaya tersebut disebut pasangan aksi-reaksi. Ingat bahwa kedua gaya tersebut (gaya aksi-gaya reaksi) bekerja pada benda yang berbeda. Berbeda dengan Hukum I Newton dan Hukum II Newton yang menjelaskan gaya yang bekerja pada benda yang sama.
Hukum gravitasi newton menyimpulkan bahwa besar gaya gravitasi yang diberikan oleh bumi pada setiap benda semakin berkurang terhadap kuadrat jaraknya (r) dari pusat bumi. Secara matematis dapat ditulis sebagai berikut:
Gaya gravitasi α 1/r2
α = sebanding
karena ada faktor massa, secara matematis ditulis sbb :
gaya gravitasi = α (Mb.MB)/r2
MB adalah massa bumi, Mb adalah massa benda lain dan r adalah jarak antara pusat bumi dan pusat benda lain.
Newton pun mencetuskan Hukum Gravitasi Universal dan mengumumkannya pada tahun 1687, hukum yang sangat terkenal dan berlaku baik di indonesia, amerika atau afrika bahkan di seluruh penjuru alam semesta. Hukum gravitasi Universal itu berbunyi demikian :
Semua benda di alam semesta menarik semua benda lain dengan gaya sebanding dengan hasil kali massa benda-benda tersebut dan berbanding terbalik dengan kuadrat jarak antara benda-benda tersebut.
Secara matematis, besar gaya gravitasi antara partikel dapat ditulis sbb :
Gaya gravitasi Fg = G m1.m2/r2 = m1. g
dan percepatan gravitasi g = Fg/m1
Fg adalah besar gaya gravitasi pada salah satu partikel, m1 dan m2 adalah massa kedua partikel, r adalah jarak antara kedua partikel.
G adalah konstanta universal yang diperoleh dari hasil pengukuran secara eksperimen. 100 tahun setelah Newton mencetuskan hukum Gravitasi Universal, pada tahun 1978, Henry Cavendish berhasil mengukur gaya yang sangat kecil antara dua benda, mirip seperti dua bola. Melalui pengukuran tersebut, Henry membuktikan dengan sangat tepat persamaan Hukum Gravitasi Universal di atas. Perbaikan penting dibuat oleh Poyting dan Boys pada abad kesembilan belas. Nilai G yang diakui sekarang = 6,67 x 10-11 Nm2/kg2
( sumber teori newton di atas dikutip dari wikipedia)
Permasalahannya, mengapa tekanan udara dan viskositas gas tidak dia perhitungkan?
Menurut aku, seharusnya . hukum gravitasi newton direvisi menjadi:
gaya gravitasi F= G M1.M2. (β o/ β h)/r2 = m1. g. (β o/ β h)
dan percepatan gravitasi g = F. β h/m1.β o
Satuannya tidak berubah, yaitu g= meter/detik2
(tapi memperhitungkan perubahan percepatan akibat tekanan udara di ketinggian tertentu dan di atas permukaan laut.
Note:
Tekanan udara berkurang dengan naiknya ketinggian tempat (elevasi atau altitude)
►Persamaan laplace
Persamaan laplace
h = k (1 + γ t)log [β o/ β h)
Pengukuran Tekanan Udara
h = ketinggian tempat
K= konstanta (18.400)
γ= koefisien pemuaian udara (0.000367)
β o= Tekanan udara pada permukaan laut
β h= Tekanan udara pada permukaan ketinggian h
Jadinya : percepatan gravitasi g = F. β h/m1.β o
Ini hanya sebatas hipotesis aku (sementara). tidak ada maksud menyaingi hukum gravitasi newton yang ada. Hukum revisi aku di atas bisa mengungkapkan angka gravitasi di dalam lautan (hanya dengan mengembangkan rumus tersebut sedikit lagi) dengan menambahkan variabel kostanta viskositas air laut di titik tersebut.
Rabu, 06 Oktober 2010
Membersihkan baju yang terkena karat sehingga berwarna kuning?
Kemudian bilas dengan sodium hipoklorit 10%. Cara membuatnya, 10 gram sodium hipoklorit (bisa di beli di toko kimia) lalu larutkan ke dalam 100 ml air.
bagaimana membuat tinta biasa menjadi berfluoresensi?
larutan A terdiri dari:
1. aesculin 100 gram
Aesculin | |
---|---|
7-hydroxy-6-{[(2S,3R,4S,5S,6R)-3,4,5-trihydroxy- 6-(hydroxymethyl)-2-tetrahydropyranyl]oxy}-2-chromenone | |
2. sodium salisilat 100 gram
3. soda kaustik / NaOH 1% sebanyak 1 ltr
selamat mencoba....
Selasa, 05 Oktober 2010
memakai maskar kain di jalanan raya?
fungsinya apa???
banyak yang tidak mengerti, terutama digunakan oleh para wanita2 kantoran saat pergi kerja dan pulang kerja di jakarta.
Masalahnya begini, polusi di jakarta paling tinggi disebabkan oleh polusi akibat kendaraan.
Asap dari kendaraan mengandung CO timbal dan gas 2 lain yang membahayakan. Terus pertanyaannya, memang seberapa besar ukuran partikel gas????
apakah bisa tersaring dengan masker2 kain seperti mereka2 itu?????????????jawabannya TIDAK
Kadang aku mikir, sebelah aku pada pakai masker kain saat naik patas ac, metromini, mikrolet....
APAKAH AKU BAU BADAN?????
hehehehehe
ternyata mereka ingin mengurangi dampak polusi. tapi salah kaprah.
ukuran partikel gas adalah mencapai satuan Amstrong.
JELAS, kain 2 tipis itu yang kurang lebih yaa... berapa se... saputangan ... tidak bisa menahan sama sekali
KECUALI pakai masker 3M yang telah dilengkapi carbon aktif dsb yang satunya mencapai 300 ribuan harganya. Jadi kalau tidak bisa menahan asap2 polusi beracun kenapa masih menggunakannya.. kan jadi aneh.. ..
Sebagai catatan, masker2 tipis itu hanya berguna untuk menahan debu2 saja yang masuk hidung. terus kalau masuk hidung, tentu tidak terlalu berbahaya, selama di hidung ada bulu hidung yang sudah diciptakan oleh Yang Kuasa untuk menahan debu sehingga timbullah (maaf!) "UPIL".
catatan juga masker2 tipis kain itu hanya berfungsi optimal kalau dalam keadaan basah. karena air akan menangkap gas beracun secara efektif.
Saran aku, gunakan masker 3 m kalau memang jenuh dengan asap polusi kendaraan.
gunakan masker kain yang agak tebal jika memang merasa tidak nyaman dengan bau2 sampah organik atau sungai yang agak bau (yang tipis se sama saja, gak nahan bau).
tapi kalau memang tetap akan jadi trend penggunaaan masker kain ini, ogut akan coba buka pabrik masker kain dengan aneka motif.. jadinya fungsinya berubah jadi lifestyle atao fashion jaman sekarang.. hehehe
hanya sekedar berbagi cerita, tidak bermaksud melarang hak kebebasan orang lain. mudah2an bermanfaat.
:D
Sabtu, 02 Oktober 2010
kenapa zat cair disebut zat cair?
Lalu mengapa kita masih membedakan materi dengan zat padat, zat cair dan gas??
bukankah lebiih bijaksana memasukkan zat cair ke dalam klasifikasi gas.
Maksudnya adalah zat cair adalah golongan gas yang viskositasnya tinggi.
bukankah gas pula menempati ruang dan mengikuti sifat menempati daerah yang lebih rendah seperti halnya cat cair. Contoh sederhana adalah gas elpiji yang selalu berada di bawah jika mengalami kebocoran.
Apakah dibalik menjadi gas adalah zat cair yang mempunyai viskositas rendah.
Silahkan Anda renungkan?
:D :D :D
kalau bingung , pegangan,,,,, hehe
Selasa, 28 September 2010
bagaimana gas huru hara itu dibuat?
Hal tersebut bisa terjadi jika kita meletakkan sebuah HCL pekat dengan kondisi terbuka, dengan NH4OH pekat (amonia) dalam keadaan terbuka secara bersebelahan. Gas putih akan terbentuk di atas larutan keduanya. Itulah SALMIAK
Senin, 27 September 2010
Mengapa atap rumah dari seng berlubang?
Jumat, 24 September 2010
Bahan baku Industri Garam
Ada alternatif bahan baku pembuatan NaCl yang murah dan sederhana.
Solusinya adalah belimbing wuluh. Buah ini mempunyai kadar garam/NaCl yang cukup tinggi.
Prosesnya dengan mengambil cairan dalama belimbing wuluh, kemudian lakukan proses kristalisasi dengan untuk mendapatkan garam yang anda inginkan. Kristalisasi bisa dengan proses penguapan, sehingga anda bisa mendaptkan kristal garam.
JIka inginn mendapatkan garam yang lebih murni, anda bisa lanjutkan dengan proses kimiawi dengan menghilangkan pengotor2 dr garam lain yang bukan senyawa NaCl.
oleloeleoeleole... :D
Selasa, 21 September 2010
Keajaiban Buah Kubis Ungu
Keajaiban Buah Kubis Ungu
Namun , kita mungkin baru mendengar bahwa ada buah yang mempunyai sifat seperti indikator, yang akan memberikan perubahan warna pada setiap perubahan pH. Bahan alam ini adalah kubis ungu. Silahkan anda coba beli kubis ungu di pasar, lalu blender, dan teteskan pada larutan asam dan basa.
Percobaan larutan asam bisa menggunakan cuka dapur (pH <7)dan percobaan pada larutan basa bisa menggunakan larutan kaustik soda(pH>7). Anda akan melihat perubahan warn yang cantik di setiap perubahan pH.
Penulis telah melakukan percobaan sederhana, Anda penasaran silahkan mencoba dan cobalah ekstraksi sehingga mendapatkan ekstrak murni. Penulis menghentikan percobaan ke tahap pemurnian, silahkan anda mencobanya.. (Lumayan buat judul skripsi, hehe...)
Sumber awal ttng kubis ungu: Anonimus
Spirtus dan Alkohol itu BEDA!
Minuman keras yang diperjual belikan dan sudah mendapatkan izin itu sebenarnya minuman keras yang mengandung alkohol dengan kadar tertentu dan sedikit citrarasa, flavour dsb.
Lalu apa bedanya dengan spirtus?
Sebagian orang mungkin berpikir bahwa spirtus dan alkohol sama saja, makanya kadang kita mendengar ada orang yang ingin memperoleh efek minuman keras rada ""greng"" dengan menambahkan spirtus. Tapi Nyatanya BEDA!!
Alkohol bisa aman untuk dikonsumsi dengan persentasi tertentu, tapi spirtus bukan untuk dikonsumsi karena itu untuk bahan kekeperluan industri.
Ciri2 fisik memang mirip dengan alkohol,namun spirtus diberikan warna biru dalam industri perdagangan.
Tau kenapa????
Hal ini justru untuk membedakanya dengan alkohol.
Lalu kenapa harus dibedakan dengan warna???
Karena alkohol dan spirtus memiliki warna yang sama jika tidak diberi pewarna. Selain itu, jika kontak dengan tangan pun, keduanya akan memberikan rasa khas keduanya, yaitu sifatnya yang mudah menguap.
Lalu kenapa dua-duanya punya sifat fisik mudah menguap tapi tetap harus dibedakan??
Karena komposisi keduanya berbeda.
Alkohol adalah tak lain etil alkohol dan minuman keras sekalipun merupakan larutan alkohol dalam air. BUKAN ALKOHOL MURNI!
dan spirtus adalah campuran alkohol dengan metanol dalam persentasi kecil.
Kenapa spirtus tidak boleh dikonsumsi???
Karena kandungan metanol didalamnnya yang bersifat racun.
Apa dampak mengkonsumsi cairan mengandung metanol??
Gangguan ritmus detak jantung, hipotensi (tekanan darah rendah), syok, gangguan kesadaran dan akhirnya koma. “Gejala keracunan pertama akan terlihat setelah periode laten beberapa jam, tanda-tandanya adalah keluhan sakit kepala, pusing, mual, muntah, gangguan penglihatan kemudian tidak sadar.
So, jangan mengkonsumsi nya.
Tulisan ini tidak mengajak kita mengkonsumsi minuma beralkohol, namun hanya sebagai pengetahuan saja buat teman-teman sebangsa, karena walau bagaimanapun minuman beralkohol itu tidakdiperbolehkan untuk dikonsumsi oleh seorang muslim.
Meningkatkan Bilangan Iod Arang Aktif!!
Arang aktif kualitasnya di tentukan dengan bilangan Iod. Arang aktif dengan bilangan Iod >1000 m2/gr harganya bisa mencapai 6500-15000 per kg nya, malah di luar negeri mencapai 20 $ US per kg nya.
Buatnya mudah, tetapi ada yg perlu diperhatikan dalam teknis prosesnya:
1. Bahan bakunya lebih baik tempurung kelapa.
2. Gunakan H3PO4 3% sebagai saat aktivasi
3. Lama aktivasi sangat menentukkan.
Penelitian penulis pada tahun 2007, bahwasanya tempurung kluwak bisa menjadi menyaingi tempurung kelapa, karena kualitas bilangan Yod bisa mencapai >1000 m2/gr (tentu dengan perlakuan khusus, dari lama aktivasi dan aktivatornya)
Alat yang anda butuhkan pun sederhana.. hanya berupa alat untuk proses pengarangan, dan alat aktivator yang didesain khusus. Teknik detilnya di lain waktu akan dijelaskan menyusul.
Produk Baru Korek Api Unik!! bukan korek kayu dan bukan korek gas!!!
Langkah membuat korek api unik.Bahannya: kertas, obat sakit gigi (cairan), dan bubuk PK (serbuk merah) yang biasa ibu2 gunakan untuk bayi waktu mandiin bayi (tanya emak, kalo gak tau!! hehehehe)
Caranya:
1. Masukkan bubuk PK ke dalam plastik es sebanyak 2 ml.Ikat plastik tersebut dengan kuat
2. masukkan plastik kecil tersebut ke dalam plastik kecil yang isinya 2 gram PK. Ikat plastik tersebut dengan kuat
3. gunting semua kelebihan plastik.
4. masukkan ke kertas, lipat rapi (hehe).
5. Tekan kertas yg berisi plastik PK yg didalamnya ada plastik obat sakit gigi sampai anda yakin kalau obat sakit gigi tersebut pecah plastiknya.
6. Biarkan 1 menit, maka anda bisa mendapatkan apinya.
Note; PK dan obat sakit gigi Anda bisa dapatkan di apotik dengan harga murah.
Penjelasan Ilmiah: Obat sakit gigi berupa senyawa gliserol akan dioksidasi oleh PK (Permanganas Kalium) sehingga PK akan mengalami reduksi menjadi Mn2+ dan gliserol teroksidasi. Reaksi nya melepaskan panas sehingga timbul api dan membakar kertas
Met mencoba!!
Bagaimana mengganti tepung terigu?
Seperti kita ketahui tepung terigu merupakan bahan pokok di setiap membuat kue, mie dll..
Adakah tepung pengganti dari terigu yang murah dan berprotein lebih tinggi??
Tepung yg dibuat dari ampas tahu merupakan sumber protein yang tinggi. Bau langu yang berasal dari kacang kedelai memang merupakan salah satu kelemahannya, namun substitusi yang proporsional dapat Anda lakukan sehingga walaupun tidak mengganti seluruhnya dengan tepung terigu, namun Anda dapat mengganti sebagian dan itu menurunkan ongkos produksi.
Langkah2 pembuatan tepung ampas tahu:
1. Beli limbah ampas tahu di pabrik-pabrik tahu. pabrik tahu kalau d i Bogor ada di daerah Kampung Muara. Anda bisa menuju kesana dari terminal bogor dengan menggunakan angkot 06 , turun di BTM, terus naik angkot 03.
2. Ampas tahu biasanya digunakan oleh para pabrik tahu untuk pakan. Tapi kalo ANda berminat anda minta saja atau dihargain dengan uang . Maksudnya uang 5000 saja , anda sudah bisa mendapatkan 5kg ampas tahu.
3. Ampas tahu bisa Anda keringkan di Sinar Matahari, lalu setlah kering, Anda ayak dengan saringan halus. Tepung ampas tahu yang sudah penulis riset, mampu mengganti 15% tepung terigu pada pembuatan mie basah. Bagaimana cara pembuatan mie basah ???ini akan penulis terangkan pada tulisan selanjutnya.
Pada komposisi 15% adalah komposisi optimal, artinya kandungan protein yang tinggi dan meningkat dibanding tepung terigu murni saja, tapi bau langu tidak tercium oleh konsumen.
Hasil peneltian ini pun telah diuji mikrobiloginya.Selama proses pembuatan tepung higienis, kita dapat menekan cemaran mikroba kapang khamir. Tekniknya, pengeringan ampas tahu dilakukan secara maksimal pada terik matahari.
Ingin Bisnis Balon Gas?
Anda pernah menemukan tukang balon gas di jalanan pakek sepada.
Kepikiran ingin menjalanin profesi ini??? tentunya kalo modal anda besar, anda gak perlu pakek sepeda lagi,. anda dirikan saja CV/ PT atau minimal jadi juragan tukang balon gas ... :D
Caranya gimana n pingin tau rahasia bisnis ini????
Alat2 dan bahan yang perlu anda sediakan:
1. logam2 seng bekas, anda bisa dapatkan di tukang besi bekas, cari aja seng2 bekas.Kalo di JKT, saya pernah liat di sepanjang jalan Ahmad Yani. (sepanjang jalan dari UKI ke Prumpung trayek mikrolet 06 A)
2. Asam Sulfat
Anda bisa dapatkan di toko2 kimia. Beli saja Asam sulfat teknis (jangan yg PA).
3. Spec tabung nya bisa tanya ama tukang tabung atau ahli tabung (cari tabung yg aman!).. hehehe... yang pasti nanti seng2 bekas nya dimasukkan ke tabung, lalu ditambahkan asam sulfat. Tabung langsung ditutup rapat.
Jika anda ingin bisnis skala besar, agar lebih murah, Anda bisa dapatkan seng 2 bekas di pengumpul dan asam sulfat bekas di pabrik2 kimia di kawasan 2 industri yg bergerak di bidang elektroplating, Banyak kok asam sulfat bekas2 degan harga murah.
Penjelasan ilmiah : Zn + H2SO4 ---> ZnSO4 + H2
H2 inilah yang kita gunakan, berupa gas.
HATI2!!
Asam sulfat bersifat korosif, jangan kena tangan, gunakan sarung tangan, kacamata.
Rahasia Sulap
Mungkin teman-temen pernah melihat pertunjukkan sulap berupa seseorang yang bisa memunculkan tulisan dari sebuh kertas hanya dengan menyemprot kertas tersebut dengan semprotan air yang biasa di pakai untuk nyemprot tanaman atau biasa kita lihat di salon2.
Ingin bisa seperti mereka atau hanya sekedar ingin mengetahui rahasianya???
Saya akan mencoba mengungkapkannya, siapa tahu teman-teman ada yang ingin menekuni profesi pesulap atau menambah koleksi teknik permainan sulapnya:
Ikuti tutorial dibawah ini:
1. Sediakan alat-alat:
a. Penyemprot air, Anda bisa mendapatkannya di toko bunga/tanaman/salon.
Bisa Anda beli disitu atau jika ada tetangga ada yang punya, pinjam hak miliknya, jadi tidak perlu dibalikkin :D (hati2 dilabrak tetangga)
b. Kertas
Jika anda ingin show hanya kepada teman2, sediakan saja kertas ukuran A4,tetapi jika anda ingin pertunjukkan agak besar, coba saja kertas ukuran koran (tanya kpd tukang koran ukurannya berapa... :D)
2. Sediakan Bahan-bahan kimia dibawah ini:
a. Caustic Soda (pellet bentuknya)
Anda bisa mendapatkannya di toko-toko kimia, bilang aja mau beli kaustik soda (kalo gak salah sekilonya gak lebih dari 10.000), Kalo yg jaga tokonya ak ngerti , bilang aja mau beli NaOH (natrium Hidroksida). Beli aja seperapat atau setengah kilo. oo yah, beli yg spesifikasi teknis ajjja.jangan yg gradenya PA (pure analysis), soalnya mahal kalo yg itu.
Setelah itu, larutkan 5 gram NaOH ke 1 ltr air, lalu masukkan ke botol penyemprot. (1.a)
2. Indikator PP (Phenolphtalein)
Anda bisa mendapatkannya di toko kimia. Bentuknya serbuk, agak mahal harganya ( 100 gram kalo gak salah 100 rbu, Coba beli saja kemasan yg udah dalam bentuk cair, agak murah (10 rebuan).
Yang bentuk cair itu isinya sebenarnya, 1 gram PP dalam 500 ml alkohol.
Kalo anda kebetulan dapatkan dalam bentuk serbuk pun entah dr teman ato dapet dr lab sekolah, anda kudu melarutkannya juga dalam 500 ml alkohol per 1 gramnya. Larutannya bening.
Cara kerjanya;
1. Oleskan larutan PP ke kertas menggunakan kuas kecil atau apapun yang ujungnya sudah dicelup ke larutan PP. seperti anda menulis dalam sebuah kertas. Tulisan tersebut bisa dapat berupa tulisan " BUKAN SULAP BUKAN MAGIC" atau "KETIPU NI YEHH" wakakak... . yang pasti tulisan tersebut di kertas gak akan terlihat oleh anda.
2. saat show, Spray dengan botol penyemprot yang sudah berisi larutan PP.
3. ENG i ENG.... muncul tulisan merah ANDA yang sebelumnya anda tulis berupa tulisan merah. (dari bekas larutan PP yg sudah kering dikertas)
Penjelasan ilmiah:
1. Larutan PP akan memberikan warna merah pada keadaan basa NaOH dan tidak akan berwarna pada suasana asam.
Hati2:
Alkohol jauhkan dari api!
Jika kaustic kena tangan, segera cuci dengan air!
PP ind. bersifat racun.
SELAMAT MENCOBA
Sabtu, 16 Januari 2010
Recycling
Recycling
From Wikipedia, the free encyclopedia
Recycling involves processing used materials (waste) into new products to prevent waste of potentially useful materials, reduce the consumption of fresh raw materials, reduce energy usage, reduce air pollution (from incineration) and water pollution (from landfilling) by reducing the need for "conventional" waste disposal, and lower greenhouse gas emissions as compared to virgin production.[1][2] Recycling is a key component of modern waste reduction and is the third component of the "Reduce, Reuse, Recycle" waste hierarchy.
Recyclable materials include many kinds of glass, paper, metal, plastic, textiles, and electronics. Although similar in effect, the composting or other reuse of biodegradable waste – such as food or garden waste – is not typically considered recycling.[2] Materials to be recycled are either brought to a collection center or picked up from the curbside, then sorted, cleaned, and reprocessed into new materials bound for manufacturing.
In a strict sense, recycling of a material would produce a fresh supply of the same material—for example, used office paper would be converted into new office paper, or used foamed polystyrene into new polystyrene. However, this is often difficult or too expensive (compared with producing the same product from raw materials or other sources), so "recycling" of many products or materials involves their reuse in producing different materials (e.g., paperboard) instead. Another form of recycling is the salvage of certain materials from complex products, either due to their intrinsic value (e.g., lead from car batteries, or gold from computer components), or due to their hazardous nature (e.g., removal and reuse of mercury from various items).
Critics dispute the net economic and environmental benefits of recycling over its costs, and suggest that proponents of recycling often make matters worse and suffer from confirmation bias. Specifically, critics argue that the costs and energy used in collection and transportation detract from (and outweigh) the costs and energy saved in the production process; also that the jobs produced by the recycling industry can be a poor trade for the jobs lost in logging, mining, and other industries associated with virgin production; and that materials such as paper pulp can only be recycled a few times before material degradation prevents further recycling. Proponents of recycling dispute each of these claims, and the validity of arguments from both sides has led to enduring controversy.
History
Early recycling
Recycling has been a common practice for most of human history, with recorded advocates as far back as Plato in 400 BC. During periods when resources were scarce, archaeological studies of ancient waste dumps show less household waste (such as ash, broken tools and pottery)—implying more waste was being recycled in the absence of new material.[3]
In pre-industrial times, there is evidence of scrap bronze and other metals being collected in Europe and melted down for perpetual reuse.[4] In Britain dust and ash from wood and coal fires was collected by 'dustmen' and downcycled as a base material used in brick making. The main driver for these types of recycling was the economic advantage of obtaining recycled feedstock instead of acquiring virgin material, as well as a lack of public waste removal in ever more densely populated areas.[3] In 1813, Benjamin Law developed the process of turning rags into 'shoddy' and 'mungo' wool in Batley, Yorkshire. This material combined recycled fibres with virgin wool. The West Yorkshire shoddy industry in towns such as Batley and Dewsbury, lasted from the early 1800s to at least 1914.
Industrialization spurred demand for affordable materials; aside from rags, ferrous scrap metals were coveted as they were cheaper to acquire than was virgin ore. Railroads both purchased and sold scrap metal in the nineteenth century, and the growing steel and automobile industries purchased scrap in the early twentieth century. Many secondary goods were collected, processed, and sold by peddlers who combed dumps, city streets, and went door to door looking for discarded machinery, pots, pans, and other sources of metal. By World War I, thousands of such peddlers roamed the streets of American cities, taking advantage of market forces to recycle post-consumer materials back into industrial production.[5]
Wartime recycling
Resource shortages caused by the world wars, and other such world-changing occurrences greatly encouraged recycling.[6] Massive government promotion campaigns were carried out in World War II in every country involved in the war, urging citizens to donate metals and conserve fibre, as a matter of significant patriotic importance. Resource conservation programs established during the war were continued in some countries without an abundance of natural resources, such as Japan, after the war ended.
Post-war recycling
The next big investment in recycling occurred in the 1970s, due to rising energy costs. Recycling aluminium uses only 5% of the energy required by virgin production; glass, paper and metals have less dramatic but very significant energy savings when recycled feedstock is used.[7]
The first recycling mill was Waste Techniques, built in Conshohocken, Pennsylvania in 1972.[citation needed] Waste Techniques was sold to Frank Keel in 1978, and resold to BFI in 1981.
Woodbury, New Jersey was the first city in the entire United States to mandate recycling.[8] Led by Rose Rowan[9] in the early 1970s, the idea of towing a "recycling" trailer behind a waste management vehicle to enable the collection of trash and recyclable material at the same time emerged. Other towns and cities soon followed suit, and today many cities in the U.S. make recycling a requirement.
In 1987, the Mobro 4000 barge hauled garbage from New York to North Carolina; where it was denied. It was then sent to Belize; where it was denied as well. Finally, the barge returned to New York and the garbage was incinerated. The incident led to heated discussions in the media about waste disposal and recycling. The incident is often referred to as igniting the recycling "hysteria" of the 1990s.[4]
Legislation
Supply
For a recycling program to work, having a large, stable supply of recyclable material is crucial. Three legislative options have been used to create such a supply: mandatory recycling collection, container deposit legislation, and refuse bans. Mandatory collection laws set recycling targets for cities to aim for, usually in the form that a certain percentage of a material must be diverted from the city's waste stream by a target date. The city is then responsible for working to meet this target.[2]
Container deposit legislation involves offering a refund for the return of certain containers, typically glass, plastic, and metal. When a product in such a container is purchased, a small surcharge is added to the price. This surcharge can be reclaimed by the consumer if the container is returned to a collection point. These programs have been very successful, often resulting in an 80% recycling rate. Despite such good results, the shift in collection costs from local government to industry and consumers has created strong opposition to the creation of such programs in some areas.[2]
A third method of increase supply of recyclates is to ban the disposal of certain materials as waste, often including used oil, old batteries, tires and garden waste. One aim of this method is to create a viable economy for proper disposal of banned products. Care must be taken that enough of these recycling services exist, or such bans simply lead to increased illegal dumping.[2]
Government-mandated demand
Legislation has also been used to increase and maintain a demand for recycled materials. Four methods of such legislation exist: minimum recycled content mandates, utilization rates, procurement policies, recycled product labeling.[2]
Both minimum recycled content mandates and utilization rates increase demand directly by forcing manufacturers to include recycling in their operations. Content mandates specify that a certain percentage of a new product must consist of recycled material. Utilization rates are a more flexible option: industries are permitted to meet the recycling targets at any point of their operation or even contract recycling out in exchange for tradeable credits. Opponents to both of these methods point to the large increase in reporting requirements they impose, and claim that they rob industry of necessary flexibility.[2][10]
Governments have used their own purchasing power to increase recycling demand through what are called "procurement policies". These policies are either "set-asides", which earmark a certain amount of spending solely towards recycled products, or "price preference" programs which provide a larger budget when recycled items are purchased. Additional regulations can target specific cases: in the United States, for example, the Environmental Protection Agency mandates the purchase of oil, paper, tires and building insulation from recycled or re-refined sources whenever possible.[2]
The final government regulation towards increased demand is recycled product labeling. When producers are required to label their packaging with amount of recycled material in the product (including the packaging), consumers are better able to make educated choices. Consumers with sufficient buying power can then choose more environmentally conscious options, prompt producers to increase the amount of recycled material in their products, and indirectly increase demand. Standardized recycling labeling can also have a positive effect on supply of recyclates if the labeling includes information on how and where the product can be recycled.[2]
Process
] Collection
A number of different systems have been implemented to collect recyclates from the general waste stream. These systems tend to lie along the spectrum of trade-off between public convenience and government ease and expense. The three main categories of collection are "drop-off centres", "buy-back centres" and "curbside collection".[2]
Drop-off centres require the waste producer to carry the recyclates to a central location, either an installed or mobile collection station or the reprocessing plant itself. They are the easiest type of collection to establish, but suffer from low and unpredictable throughput. Buy-back centres differ in that the cleaned recyclates are purchased, thus providing a clear incentive for use and creating a stable supply. The post-processed material can then be sold on, hopefully creating a profit. Unfortunately government subsidies are necessary to make buy-back centres a viable enterprise, as according to the United States Nation Solid Wastes Management Association it costs on average US$50 to process a ton of material, which can only be resold for US$30.[2]
Curbside collection
Main article: Curbside collection
Curbside collection encompasses many subtly different systems, which differ mostly on where in the process the recyclates are sorted and cleaned. The main categories are mixed waste collection, commingled recyclables and source separation.[2] A waste collection vehicle generally picks up the waste.
At one end of the spectrum is mixed waste collection, in which all recyclates are collected mixed in with the rest of the waste, and the desired material is then sorted out and cleaned at a central sorting facility. This results in a large amount of recyclable waste, paper especially, being too soiled to reprocess, but has advantages as well: the city need not pay for a separate collection of recyclates and no public education is needed. Any changes to which materials are recyclable is easy to accommodate as all sorting happens in a central location.[2]
In a Commingled or single-stream system, all recyclables for collection are mixed but kept separate from other waste. This greatly reduces the need for post-collection cleaning but does require public education on what materials are recyclable.[2][4]
Source separation is the other extreme, where each material is cleaned and sorted prior to collection. This method requires the least post-collection sorting and produces the purest recyclates, but incurs additional operating costs for collection of each separate material. An extensive public education program is also required, which must be successful if recyclate contamination is to be avoided.[2]
Source separation used to be the preferred method due to the high sorting costs incurred by commingled collection. Advances in sorting technology (see sorting below), however, have lowered this overhead substantially—many areas which had developed source separation programs have since switched to comingled collection.[4]
Sorting
Once commingled recyclates are collected and delivered to a central collection facility, the different types of materials must be sorted. This is done in a series of stages, many of which involve automated processes such that a truck-load of material can be fully sorted in less than an hour.[4] Some plants can now sort the materials automatically, known as single-stream recycling. A 30 percent increase in recycling rates has been seen in the areas where these plants exist.[11]
Initially, the commingled recyclates are removed from the collection vehicle and placed on a conveyor belt spread out in a single layer. Large pieces of corrugated fiberboard and plastic bags are removed by hand at this stage, as they can cause later machinery to jam.[4]
Next, automated machinery separates the recyclates by weight, splitting lighter paper and plastic from heavier glass and metal. Cardboard is removed from the mixed paper, and the most common types of plastic, PET (#1) and HDPE (#2), are collected. This separation is usually done by hand, but has become automated in some sorting centers: a spectroscopic scanner is used to differentiate between different types of paper and plastic based on the absorbed wavelengths, and subsequently divert each material into the proper collection channel.[4]
Strong magnets are used to separate out ferrous metals, such as iron, steel, and tin-plated steel cans ("tin cans"). Non-ferrous metals are ejected by magnetic eddy currents in which a rotating magnetic field induces an electric current around the aluminium cans, which in turn creates a magnetic eddy current inside the cans. This magnetic eddy current is repulsed by a large magnetic field, and the cans are ejected from the rest of the recyclate stream.[4]
Finally, glass must be sorted by hand based on its color: brown, amber, green or clear.[4]
Cost-benefit analysis
+ Environmental effects of recycling[12] | ||
Material | Energy Savings | Air Pollution Savings |
---|---|---|
Aluminium | 95%[2][7] | 95%[2][13] |
Cardboard | 24% | — |
Glass | 5-30% | 20% |
Paper | 40%[7] | 73% |
Plastics | 70%[7] | — |
Steel | 60%[4] | — |
There is some debate over whether recycling is economically efficient. Municipalities often see fiscal benefits from implementing recycling programs, largely due to the reduced landfill costs.[14] A study conducted by the Technical University of Denmark found that in 83% of cases, recycling is the most efficient method to dispose of household waste.[4][7] However, a 2004 assessment by the Danish Environmental Assessment Institute concluded that incineration was the most effective method for disposing of drink containers, even aluminium ones.[15]
Fiscal efficiency is separate from economic efficiency. Economic analysis of recycling includes what economists call externalities, which are unpriced costs and benefits that accrue to individuals outside of private transactions. Examples include: decreased air pollution and greenhouse gases from incineration, reduced hazardous waste leaching from landfills, reduced energy consumption, and reduced waste and resource consumption, which leads to a reduction in environmentally damaging mining and timber activity. About 4,000 minerals have been identified, of these around 100 can be called common, another several hundred are relatively common, and the rest are rare.[16] Without more recycling, zinc could be used up by 2037, both indium and hafnium could run out by 2017, and terbium could be gone before 2012.[17] At current rates, reserves of phosphorus will be depleted in the next 50 to 100 years.[18][19] Without mechanisms such as taxes or subsidies to internalize externalities, businesses will ignore them despite the costs imposed on society. To make such non-fiscal benefits economically relevant, advocates have pushed for legislative action to increase the demand for recycled materials.[2] The United States Environmental Protection Agency (EPA) has concluded in favor of recycling, saying that recycling efforts reduced the country's carbon emissions by a net 49 million metric tonnes in 2005.[4] In the United Kingdom, the Waste and Resources Action Programme stated that Great Britain's recycling efforts reduce CO2 emissions by 10-15 million tonnes a year.[4] Recycling is more efficient in densely populated areas, as there are economies of scale involved.[2]
Certain requirements must be met for recycling to be economically feasible and environmentally effective. These include an adequate source of recyclates, a system to extract those recyclates from the waste stream, a nearby factory capable of reprocessing the recyclates, and a potential demand for the recycled products. These last two requirements are often overlooked—without both an industrial market for production using the collected materials and a consumer market for the manufactured goods, recycling is incomplete and in fact only "collection".[2]
Many economists favor a moderate level of government intervention to provide recycling services. Economists of this mindset probably view product disposal as an externality of production and subsequently argue government is most capable of alleviating such a dilemma. However, those of the laissez faire approach to municipal recycling see product disposal as a service that consumers value. A free-market approach is more likely to suit the preferences of consumers since profit-seeking businesses have greater incentive to produce a quality product or service than does government. Moreover, economists most always advise against government intrusion in any market with little or no externalities.” [20]
Trade in recyclates
Certain countries trade in unprocessed recyclates. Some have complained that the ultimate fate of recyclates sold to another country is unknown and they may end up in landfills instead of reprocessed. According to one report, in America, 50-80% of computers destined for recycling are actually not recycled.[21][22] There are reports of illegal-waste imports to China being dismantled and recycled solely for monetary gain, without consideration for workers' health or environmental damage. Though the Chinese government has banned these practices, it has not been able to eradicate them.[23] In 2008, the prices of recyclable waste plummeted before rebounding in 2009. Cardboard averaged about £53/tonne from 2004–2008, dropped to £19/tonne, and then went up to £59/tonne in May 2009. PET plastic averaged about £156/tonne, dropped to £75/tonne and then moved up to £195/tonne in May 2009.[24] Certain regions have difficulty using or exporting as much of a material as they recycle. This problem is most prevalent with glass: both Britain and the U.S. import large quantities of wine bottled in green glass. Though much of this glass is sent to be recycled, outside the American Midwest there is not enough wine production to use all of the reprocessed material. The extra must be downcycled into building materials or re-inserted into the regular waste stream.[2][4]
Similarly, the northwestern United States has difficulty finding markets for recycled newspaper, given the large number of pulp mills in the region as well as the proximity to Asian markets. In other areas of the U.S., however, demand for used newsprint has seen wide fluctuation.[2]
In some U.S. states, a program called RecycleBank pays people with coupons to recycle, receiving money from local municipalities for the reduction in landfill space which must be purchased. It uses a single stream process in which all material is automatically sorted.[25]
Criticism
| This section may require cleanup to meet Wikipedia's quality standards. Please improve this section if you can. (May 2009) |
Main article: Sustainable design
Much of the difficulty inherent in recycling comes from the fact that most products are not designed with recycling in mind.[citation needed] The concept of sustainable design aims to solve this problem, and was laid out in the book "Cradle to Cradle: Remaking the Way We Make Things" by architect William McDonough and chemist Michael Braungart. They suggest that every product (and all packaging they require) should have a complete "closed-loop" cycle mapped out for each component—a way in which every component will either return to the natural ecosystem through biodegradation or be recycled indefinitely.[4]
As with environmental economics, care must be taken to ensure a complete view of the costs and benefits involved. For example, cardboard packaging for food products is more easily recycled than plastic, but is heavier to ship and may result in more waste from spoilage.[26]
The following are criticisms of many popular points used for recycling.
Saves energy
There is controversy on just how much energy is saved through recycling. The Energy Information Administration (EIA) states on its website that "a paper mill uses 40 percent less energy to make paper from recycled paper than it does to make paper from fresh lumber."[27] Critics often argue that in the overall processes, it can take more energy to produce recycled products than it does to dispose of them in traditional landfill methods. This argument is followed from the curbside collection of recyclables, which critics note is often done by a second waste truck. Recycling proponents point out that a second timber or logging truck is eliminated when paper is collected for recycling.
It is difficult to determine the exact amount of energy consumed or produced in waste disposal processes. How much energy is used in recycling depends largely on the type of material being recycled and the process used to do so. Aluminium is generally agreed to use far less energy when recycled rather than being produced from scratch. The EPA states that "recycling aluminum cans, for example, saves 95 percent of the energy required to make the same amount of aluminum from its virgin source, bauxite."[28]
Economist Steven Landsburg has suggested that the sole benefit of reducing landfill space is trumped by the energy needed and resulting pollution from the recycling process.[29] Others, however, have calculated through life cycle assessment that producing recycled paper uses less energy and water than harvesting, pulping, processing, and transporting virgin trees.[30] When less recycled paper is used, additional energy is needed to create and maintain farmed forests until these forests are as self-sustainable as virgin forests.
Saves money
The amount of money actually saved through recycling depends on the efficiency of the recycling program used to do it. The Institute for Local Self-Reliance argues that the cost of recycling depends on various factors around a community that recycles, such as landfill fees and the amount of disposal that the community recycles. It states that communities start to save money when they treat recycling as a replacement for their traditional waste system rather than an add-on to it and by "redesigning their collection schedules and/or trucks."[31]
In many cases, the cost of recyclable materials also exceeds the cost of raw materials. Virgin plastic resin costs 40% less than recycled resin.[32] Additionally, a United States Environmental Protection Agency (EPA) study that tracked the price of clear glass from July 15 to August 2, 1991, found that the average cost per ton ranged from $40 to $60,[33] while a USGS report shows that the cost per ton of raw silica sand from years 1993 to 1997 fell between $17.33 and $18.10.[34]
In a 1996 article for The New York Times, John Tierney argued that it costs more money to recycle the trash of New York City than it does to dispose of it in a landfill. Tierney argued that the recycling process employs people to do the additional waste disposal, sorting, inspecting, and many fees are often charged because the processing costs used to make the end product are often more than the profit from its sale.[35] Tierney also referenced a study conducted by the Solid Waste Association of North America (SWANA) that found in the six communities involved in the study, "all but one of the curbside recycling programs, and all the composting operations and waste-to-energy incinerators, increased the cost of waste disposal."[36]
Tierney also points out that "the prices paid for scrap materials are a measure of their environmental value as recyclables. Scrap aluminum fetches a high price because recycling it consumes so much less energy than manufacturing new aluminum."
Working conditions
Critics often argue that while recycling may create jobs, they are often jobs with low wages and terrible working conditions.[37] These jobs are sometimes considered to be make-work jobs that don't produce as much as the cost of wages to pay for those jobs. In areas without many environmental regulations and/or worker protections, jobs involved in recycling such as ship breaking can result in deplorable conditions for both workers and the surrounding communities.
Recycling proponents counter that the jobs involved in recovery of an equal amount of virgin material creates worse jobs. Timber harvesting and ore mining are more dangerous than paper recycling and metal recycling.[citation needed]
Saves trees
Economist Steven Landsburg, author of a paper entitled "Why I Am Not an Environmentalist," [38] has claimed that paper recycling actually reduces tree populations. He argues that because paper companies have incentives to replenish the forests they own, large demands for paper lead to large forests. Conversely, reduced demand for paper leads to fewer "farmed" forests.[39] Similar arguments were expressed in a 1995 article for The Free Market.[40]
When foresting companies cut down trees, more are planted in their place. Most paper comes from pulp forests grown specifically for paper production.[41][36][40][42] Many environmentalists point out, however, that "farmed" forests are inferior to virgin forests in several ways. Farmed forests are not able to fix the soil as quickly as virgin forests, causing widespread soil erosion and often requiring large amounts of fertilizer to maintain while containing little tree and wild-life biodiversity compared to virgin forests.[43] Also, the new trees planted are not as big as the trees that were cut down, and the argument that there will be "more trees" is not compelling to forestry advocates when they are counting saplings.
The recycling of paper should not be confused with saving the tropical forest. Many people have the misconception that paper-making is what's causing deforestation of tropical rain forests but rarely any tropical wood is harvested for paper. Deforestation is mainly caused by population pressure such as demand of more land for agriculture or construction use. Therefore, the recycling paper, although reduces demand of trees, doesn't greatly benefit the tropical rain forests.[44]
Possible income loss and social costs
| This section may contain original research. Please improve it by verifying the claims made and adding references. Statements consisting only of original research may be removed. More details may be available on the talk page. (July 2010) |
In some prosperous and many less prosperous countries in the world, the traditional job of recycling is performed by the entrepreneurial poor such as the karung guni, Zabaleen, the rag and bone man, waste picker, and junk man. With the creation of large recycling organizations that may be profitable, either by law or economies of scale,[45][46] the poor are more likely to be driven out of the recycling and the remanufacturing market. To compensate for this loss of income to the poor, a society may need to create additional forms of societal programs to help support the poor.[47] Like the parable of the broken window, there is a net loss to the poor and possibly the whole of a society to make recycling artificially profitable through law. However, as seen in Brazil and Argentina, waste pickers/informal recyclers are able to work alongside governments, in (semi)funded cooperatives, allowing informal recycling to be legitimized as a paying government job.[48]
Because the social support of a country is likely less than the loss of income to the poor doing recycling, there is a greater chance that the poor will come in conflict with the large recycling organizations.[49][50] This means fewer people can decide if certain waste is more economically reusable in its current form rather than being reprocessed. Contrasted to the recycling poor, the efficiency of their recycling may actually be higher for some materials because individuals have greater control over what is considered “waste.”[47]
One labor-intensive underused waste is electronic and computer waste. Because this waste may still be functional and wanted mostly by the poor, the poor may sell or use it at a greater efficiency than large recyclers.
Many recycling advocates believe that this laissez-faire individual-based recycling does not cover all of society’s recycling needs. Thus, it does not negate the need for an organized recycling program.[47] Local government often consider the activities of the recycling poor as contributing to property blight.
Newsprint
There are upper limits on the percentage of the world’s newsprint that can be manufactured from recycled fiber. The most obvious upper limit is imposed by the nature of recycling itself. Some of the fiber that enters any recycled pulp mill is lost in pulping, due to inefficiencies inherent in the process. According to the web site of the U.K. chapter of Friends of the Earth[51] wood fiber can normally only be recycled up to five times due to damage experienced to the fiber. Thus, unless the quantity of newsprint used each year worldwide declines to reflect the lost fiber, a certain amount of new (virgin) fiber is required each year globally, even if the individual newsprint mill may continue to use 100% recycled fiber.
Additionally, some old newspapers never make it to a recycling plant, being used for a variety of household and industrial applications or simply ending up in landfill. Recycle rates (the percentage of annual newsprint consumption which is then recycled) vary from country to country and, within countries, from city to rural areas as well as from city to city. The American Forest & Paper Association estimates that more than 72% of newsprint produced in North America in 2006 was recovered for re-use or export, with about 58% of that going back to a paper or paperboard mill for re-use, 16% being used by molded pulp mills (to make products such as egg cartons) and the balance being shipped offshore. Of the percentage that is re-used by a North American paper or paperboard mill, AFPA estimates that about a third goes back into newsprint manufacture. Recycle rates can also vary over time with the price paid by the market for old newspapers, which can be quite volatile. As an example, in recent years, with China growing as a manufacturer of various kinds of paper and packaging – using significant quantities of recycled fiber imported from the U.S. and elsewhere – its demand for old newspapers has at times been strong enough to influence recycled fiber prices worldwide. While high recycled fiber prices are good news for the goal of reducing landfill quantities, they can affect the profitability of newsprint mills using recycled fibers.
An important consideration in fiber selection by newsprint mills aside from cost is the high speeds of both modern newsprint machines and modern newspaper printing presses. There are newsprint machines in the U.S. operating at speeds approaching 1,400 meters per minute, according to industry information group RISI Inc., while the newest machines in the world (including some recently installed in China) can have speeds topping 1,800 meters per minute. Modern newspaper presses can run at speeds of up to 90,000 copies per hour (according to publishing industry association IFRA), with a few approaching 100,000 cph.
Such high speeds place severe demands on the strength of the sheet, both on the paper machine during the manufacturing process and on the press during printing. A number of newsprint mills around the world manufacture commercially acceptable qualities of newsprint using 100% recycled fiber. However, such mill operators must be very selective about the purity of the waste stream, making sure they employ a minimum of contaminants and include as much long-fibered old newsprint as possible. Virgin newsprint is made from long-fibered (softwood) trees such as spruce, fir, balsam and pine, while some paper and paperboard products are manufactured from shorter-fibered hardwood species. Newsprint mills prefer to use old newspapers, or a mix of old newspapers and old magazines, rather than recycling other paper grades. As U.S. municipalities have recently moved toward “single stream” recycling – collecting various waste products in a single compartment of a vehicle – mills have been forced to spend more money to procure a clean, appropriate waste stream for pulping purposes.
In the United States
In a 1996 article in The New York Times, John Tierney claimed that government mandated recycling wastes more resources than it saves.[26] Some highlights from the article:
- In cases where recycling truly does save resources, such as with large scraps of aluminium, this will be reflected in market prices, and voluntary recycling will take place. Thus, there is no need for the government to mandate it.
- Adopting a 'pay-as-you-throw' scheme would motivate people to find out "what's worth diverting to a recycling bin" so there would be no need for recycling laws. This has been supported by some environmental groups as well.
- Tree farmers plant more trees than they cut down.
- Government mandated recycling is more expensive than putting the garbage into landfills.
- Some small towns with landfills are happy to import garbage from other cities and states because it provides jobs and tax revenue.
- Today's modern landfills are much cleaner and safer, and much less likely to leak and pollute than the landfills of the past.
- Incinerators make more energy than recycling saves. Also, some things, such as glossy paper, can't be recycled, and it is better to burn such materials for energy.
- Regarding the claim that the U.S. is running out of landfill space, Tierney wrote, "A. Clark Wiseman, an economist at Gonzaga University in Spokane, Washington, has calculated that if Americans keep generating garbage at current rates for 1,000 years, and if all their garbage is put in a landfill 100 yards (91 m) deep, by the year 3000 this national garbage heap will fill a square piece of land 35 miles (56 km) on each side. This doesn't seem a huge imposition in a country the size of America. The garbage would occupy only 5 percent of the area needed for the national array of solar panels proposed by environmentalists. The millennial landfill would fit on one-tenth of 1 percent of the range land now available for grazing in the continental United States. And if it still pains you to think of depriving posterity of that 35-mile (56 km) square, remember that the loss will be only temporary. Eventually, like previous landfills, the mounds of trash will be covered with grass and become a minuscule addition to the nation's 150,000 square miles (390,000 km2) of parkland."
Tierney's article received a referenced critique from the Environmental Defense Fund, which noted that "the article relied heavily on quotes and information supplied by a group of consultants and think tanks that have strong ideological objections to recycling".[52] In 2003, the city of Santa Clarita, California was paying $28 per ton to put garbage into a landfill. The city then adopted a mandatory diaper recycling program that cost $1,800 per ton.[53] In a 2007 article, Michael Munger, the Chair of Political Science at Duke University, wrote, "... if recycling is more expensive than using new materials, it can't possibly be efficient... There is a simple test for determining whether something is a resource... or just garbage... If someone will pay you for the item, it's a resource... But if you have to pay someone to take the item away... then the item is garbage."[54] In a 2002 article for The Heartland Institute, Jerry Taylor, director of natural resource studies at the Cato Institute, wrote, "If it costs X to deliver newly manufactured plastic to the market, for example, but it costs 10X to deliver reused plastic to the market, we can conclude the resources required to recycle plastic are 10 times more scarce than the resources required to make plastic from scratch. And because recycling is supposed to be about the conservation of resources, mandating recycling under those circumstances will do more harm than good."[55] In 2002, WNYC reported that 40% of the garbage that New York City residents separated for recycling actually ended up in landfills.[56]
Common recyclables
Many different materials can be recycled but each type requires a different technique.
Builders' waste
Aggregates and concrete
Main article: Concrete recycling
Concrete aggregate collected from demolition sites is put through a crushing machine, often along with asphalt, bricks, dirt, and rocks. Smaller pieces of concrete are used as gravel for new construction projects. Crushed recycled concrete can also be used as the dry aggregate for brand new concrete if it is free of contaminants. Builder's rubble (like broken down bricks) is also used for railway balast and gravel paths. This reduces the need for other rocks to be dug up, which in turn saves trees and habitats.[57]
Asphalt roof shingles and tarmac
Asphalt shingle are generally melted down and in part recycled. Tarmac can also be melted down, but it is too costly to do economically.
Drywall
Because up to 17% of drywall is wasted during the manufacturing and installation processes and the drywall (USA) or plasterboard (UK and Ireland) material is frequently not re-used, disposal can become a problem. Some landfill sites have banned the dumping of drywall. Some manufacturers take back waste wallboards from construction sites and recycle it into new wallboard. Recycled paper is typically used during manufacturing. More recently, recycling at the construction site itself is being investigated. There is potential for using crushed drywall to amend certain soils at building sites, such as clay and silt mixtures (bay mud), as well as using it in compost.[58]
Batteries
Main article: Battery recycling
The large variation in size and type of batteries makes their recycling extremely difficult: they must first be sorted into similar kinds and each kind requires an individual recycling process. Additionally, older batteries contain mercury and cadmium, harmful materials that must be handled with care. Because of their potential environmental damage, proper disposal of used batteries is required by law in many areas. Unfortunately, this mandate has been difficult to enforce.[61]
Lead-acid batteries, like those used in automobiles, are relatively easy to recycle and many regions have legislation requiring vendors to accept used products. In the United States, the recycling rate is 90%, with new batteries containing up to 80% recycled material.[61]
Japan, Kuwait, the USA, Canada, France, the Netherlands, Germany, Austria, Belgium, Sweden, the UK and Ireland all actively encourage battery recycling programs.[59][60][62] [63] In 2006 the EU passed the Battery Directive of which one of the aims is a higher rate of battery recycling. The EU directive said a at least 25% of all the EU’s used batteries must be collected by 2012, and rising to no les than 45% by 2016, of which, that at least 50% of them must be recycled.[63]
The % of battery recycled in the EU was roughly at this level in 2006-
Nation | % Recycled | Source |
---|---|---|
Belgium | 59% | [63] |
Sweden | 55% | [63] |
Austria | 44% | [63] |
Germany | 39% | [63] |
The Netherlands | 32% | [63] |
France | 16% | [63] |
Main article: Automotive battery recycling
These batteries include but are not limited to: car batteries, golf cart batteries, UPS batteries, industrial fork-lift batteries, motorcycle batteries, and commercial batteries.
Biodegradable waste
Main article: Composting
Kitchen, garden, and other green waste can be recycled into useful material by composting. This process allows natural aerobic bacteria to break down the waste into fertile topsoil. Much composting is done on a household scale, but municipal green-waste collection programs also exist. These programs can supplement their funding by selling the topsoil produced.
Clothes and textiles (cloth)
Clothing
Recycling clothes via consignment or swapping has become increasingly popular. In a clothing swap, a group of people gather at a venue to exchange clothes amongst each other. In organizations like Clothing Swap, Inc., unclaimed clothing is donated to a local charity.
Textiles
Main article: Textile recycling
When considering textile recycling one must understand what the material consists of. Most textiles are composites of cotton (biodegradable material) and synthetic plastics. The textile's composition will affect its durability and method of recycling.
Workers sort and separate collected textiles into good quality clothing and shoes which can be reused or worn. There is a trend of moving these facilities from developed countries to developing countries either for charity or sold at a cheaper price.[64] Many international organisations collect used textiles from developed countries as a donation to those third world countries. This recycling practise is encouraged because it helps to reduce unwanted waste while providing clothing to those in need.[65] Damaged textiles are further sorted into grades to make industrial wiping cloths and for use in paper manufacture or material suitable for fibre reclamation and filling products. If textile reprocessors receive wet or soiled clothes however, these may still be disposed of in a landfill, as the washing and drying facilities are not present at sorting units.[66]
Fibre reclamation mills sort textiles according to fibre type and colour. Colour sorting eliminates the need to re-dye the recycled textiles. The textiles are shredded into "shoddy" fibres and blended with other selected fibres, depending on the intended end use of the recycled yarn. The blended mixture is carded to clean and mix the fibres and spun ready for weaving or knitting. The fibres can also be compressed for mattress production. Textiles sent to the flocking industry are shredded to make filling material for car insulation, roofing felts, loudspeaker cones, panel linings and furniture padding.
Electronic waste
Electronics disassembly and reclamation
Main article: Computer recycling
Computer recycling or Electronic recycling is the recycling or reuse of computers or other electronics. It includes both finding another use for materials (such as donation to charity), and having systems dismantled in a manner that allows for the safe extraction of the constituent materials for reuse in other products. The direct disposal of electrical equipment—such as old computers and mobile phones is banned in many areas, such as the UK, parts of the USA, Japan, Ireland, Germany and the Netherlands, due to the toxic contents of certain components. The recycling process works by mechanically separating the metals, plastics, and circuit boards contained in the appliance. When this is done on a large scale at an electronic waste recycling plant, component recovery can be achieved in a cost-effective manner. The National Association for Information Destruction (NAID) “is the international trade association for companies providing information destruction services. They are suppliers of products, equipment and services to destruction companies are also eligible for membership. NAID's mission is to promote the information destruction industry and the standards and ethics of its member companies.” [67] There are companies that follow the guidelines from NAID and also meet all Federal EPA and local DEP regulations. A special computer shredder is used to destroy computers and phones,[68][69] and.[70]
With high lead content in CRTs, and the rapid diffusion of new, flat-panel display technologies, some of which (LCDs) use lamps containing mercury, there is growing concern about electronic waste from discarded televisions. Related occupational health concerns exist, as well, for disassemblers and scrap dealers removing copper wiring and other materials from CRTs. Further environmental concerns related to television design and use relate to the devices' increasing electrical energy requirements.[71]
Computers that are turmed Trashware in North America or Totaly reconditioned hardware in the UK and Ireland are computer equipment that has assembled from old hardware, using cleaned and checked parts from different computers, for use by disadvantaged people to bridge the digital divide.
Trashware, with its 'green' social aims, is different from retrocomputing, which has only cultural and recreational purposes.
Ink jet printer cartridges
Because printer cartridges from the original manufacturer are often expensive, demand exists for cheaper third party options. These include ink sold in bulk, cartridge refill kits, machines in stores that automatically refill cartridges, remanufactured cartridges, and cartridges made by an corporate entity other than the original manufacturer.
Consumers can refill ink cartridges themselves with a kit, or they can take the cartridge to a refiller or remanufacturer where ink is pumped back into the cartridge. PC World reports that refilled cartridges have higher failure rates, print fewer pages than new cartridges, and demonstrate more on-page problems like streaking, curling, and colour bleed.[72]
Paint
Main article: Paint recycling
Paint is often collected at government-run Household Hazardous Waste facilities. From there, it is taken to paint recyclers, where it is sorted by quality. Uses for paint that cannot be reprocessed and resold vary by recycler.
Metals
Ferrous metals
Main article: Steel recycling
Iron and steel are the world's most recycled materials, and among the easiest materials to reprocess, as they can be separated magnetically from the waste stream. Recycling is via a steelworks: scrap is either remelted in an electric arc furnace (90-100% scrap), or used as part of the charge in a Basic Oxygen Furnace (around 25% scrap).[73] Any grade of steel can be recycled to top quality new metal, with no 'downgrading' from prime to lower quality materials as steel is recycled repeatedly. 42% of crude steel produced is recycled material.[74]
Non-ferrous metals
Main article: Aluminium recycling
Aluminium is one of the most efficient and widely recycled materials.[75][76] Aluminium is shredded and ground into small pieces or crushed into bales. These pieces or bales are melted in an aluminium smelter to produce molten aluminium. By this stage, the recycled aluminium is indistinguishable from virgin aluminium and further processing is identical for both. This process does not produce any change in the metal, so aluminium can be recycled indefinitely.
Recycling aluminium saves 95% of the energy cost of processing new aluminium.[7] This is because the temperature necessary for melting recycled, nearly pure, aluminium is 600 °C, while to extract mined aluminium from its ore requires 900 °C. To reach this higher temperature, much more energy is needed, leading to the high environmental benefits of aluminium recycling. Americans throw away enough aluminium every year to rebuild their entire commercial air fleet. Also, the energy saved by recycling one aluminium can is enough to run a television for three hours.[13]
Glass
Main article: Glass recycling
Glass bottles and jars are gathered by a curbside collection truck and bottle banks, where the glass may be sorted into color categories. The collected glass cullet is taken to a glass recycling plant where it is monitored for purity and contaminants are removed. The cullet is crushed and added to a raw material mix in a melting furnace. It is then mechanically blown or molded into new jars or bottles. Glass cullet is also used in the construction industry for aggregate and glassphalt. Glassphalt is a road-laying material which comprises around 30% recycled glass. Glass can be recycled indefinitely as its structure does not deteriorate when reprocessed.
Paper and newsprint
Main article: Paper recycling
Both paper and newsprint can be recycled by reducing it to pulp and combining it with pulp from newly harvested wood. As the recycling process causes the paper fibres to break down, each time paper is recycled its quality decreases. This means that either a higher percentage of new fibres must be added, or the paper downcycled into lower quality products. Any writing or colouration of the paper must first be removed by deinking, which also removes fillers, clays, and fibre fragments.[77]
Almost all paper can be recycled today, but some types are harder to recycle than others. Papers coated with plastic or aluminium foil, and papers that are waxed, pasted, or gummed are usually not recycled because the process is too expensive. Gift-wrap paper also cannot be recycled due to its already poor quality.[77]
Sometimes recyclers ask for the removal of the glossy paper inserts from newspapers because they are a different type of paper. Glossy inserts have a heavy clay coating that some paper mills cannot accept. Most of the clay is removed from the recycled pulp as sludge, which must be disposed of. If the coated paper is 20% by weight clay, then each ton of glossy paper produces more than 200 kg of sludge and less than 800 kg of fibre.[77]
The price of recycled paper has varied greatly over the last 30 or so years.[78][79] [80][81] [82][83][84] The German price of €100/£49 per tonne was typical for the year 2003 [81] and it steadily rose over the years. By the September of 2008 saw the American price of $235 per ton, which had fallen to just $120 per ton,[78] and in the January of 2009, the UK's fell six weeks from about £70.00 per ton, to only £10.00 per ton.[79][82] The slump was probably due to the economic down turn in East Asia leading to market for waste paper drying up in China.[82] 2010 averaged at $120.32 over the start of the year, but saw a rapid rise global prices in May 2010,[80] with the June 2010 resting $217.11 per ton in the USA as China's paper market began to reopen[80]!
Mexico, America, the EU, Russia and Japan all recycle paper on mass and there are many state run and private sceams running in tose countries. In 2004 the paper recycling rate in Europe was 54.6% or 45.5 million short tons (41.3 Mt).[85] The recycling rate in Europe reached 64.5%3 in 2007, which confirms that the industry is on the path to meeting its voluntary target of 66% by 2010.[86]
Plastic
Main article: Plastic recycling
Plastic recycling is the process of recovering scrap or waste plastics and reprocessing the material into useful products. Compared to glass or metallic materials, plastic poses unique challenges. Because of the massive number of types of plastic, they each carry a resin identification code, and must be sorted before they can be recycled. This can be costly; while metals can be sorted using electromagnets, no such 'easy sorting' capability exists for plastics. In addition to this, while labels do not need to be removed from bottles for recycling, lids are often made from a different kind of non-recyclable plastic.
To help in identifying the materials in various plastic items, resin identification code numbers 1-6 have been assigned to six common kinds of recyclable plastic resins, with the number 7 indicating any other kind of plastic, whether recyclable or not. Standardized symbols are available incorporating each of these resin codes.
Timber
Main article: Timber recycling
Recycling timber has become popular due to its image as an environmentally friendly product, with consumers commonly believing that by purchasing recycled wood the demand for green timber will fall and ultimately benefit the environment. Greenpeace also view recycled timber as an environmentally friendly product, citing it as the most preferable timber source on their website. The arrival of recycled timber as a construction product has been important in both raising industry and consumer awareness towards deforestation and promoting timber mills to adopt more environmentally friendly practices.
Wood recycling is a subject that has an ever-greater role in our lives in recent years taken. The problem, however, is that although many local authorities like the idea of recycling, they do not fully support it. One of the countless examples, which has been in the news is the concept of actually recycling wood which is growing in the cities. Namely, recycling timber, trees and other sources.[87]
Other techniques and materiels
Several other materials are also commonly recycled, frequently at an industrial level.
Rubber tyers
Tire recycling or Rubber recycling is the process of recycling vehicles tires (or tyres) that are no longer suitable for use on vehicles due to wear or irreparable damage (such as punctures). These tires are among the largest and most problematic sources of waste, due to the large volume produced and their durability. Those same characteristics which make waste tires such a problem also make them one of the most re-used waste materials, as the rubber is very resilient and can be reused in other products. Approximately one tire is discarded per person per year. Tires are also often recycled for use on basketball courts and new shoe products. However material recovered from waste tires, known as "crumb" is generally only a cheap "filler" material and is rarely used in high volumes. Tire recycling is also faily common. Used tires can be added to asphalt for producing road surfaces or to make rubber mulch used on playgrounds for safety. They are also often used as the insulation and heat absorbing/releasing material in specially constructed homes known as earthships. It is arguable that tire crumb in applications such as basketball courts could be better described as "reused" rubber rather than "recycled".
Chat and furnace slag
Mining's chat waste can be used to snow-covered roads to improve traction; as gravel; and as construction aggregate, principally for railroad ballast, highway construction, and concrete production in North America. Furnace slag and to a lesser degree coal slag have been used in liue of construction and railway balast gravel in the UK. Clinker, slag, fly ash and in some cases ashes have all been historicly used in places like the industrial parts of Yorkshire and South Wales to make domestic cinder paths with.
Ship breaking
Ship breaking or ship demolition is a type of ship disposal involving the breaking up of ships for scrap recycling, with the hulls being discarded in ship graveyards. Most ships have a lifespan of a few decades before there is so much wear that refitting and repair becomes uneconomical. Ship breaking allows materials from the ship, especially steel, to be reused. Equipment on board the vessel can also be reused. Until the late 20th century, ship breaking took place in port cities of industrialized countries such as the United Kingdom and the United States. Today, most ship breaking yards are in Alang in India, Chittagong in Bangladesh, Aliağa in Turkey and Gadani near Karachi in Pakistan. Ship breaking is one example that has associated environmental, health, and safety risks for the area where the operation takes place; balancing all these considerations is an environmental justice problem.
Waste water
Sewage treatment, or domestic wastewater treatment, is the process of removing contaminants from wastewater and household sewage, both runoff (effluents) and domestic. It includes physical, chemical, and biological processes to remove physical, chemical and biological contaminants. Its objective is to produce a waste stream (or treated effluent) and a solid waste or sludge suitable for discharge or reuse back into the environment. This material is often inadvertently contaminated with many toxic organic and inorganic compounds. This is generaly done at the local sewerage works on an industrial basis using chemical, sedimentation, floculation and flitration purification techniques.
Source : http://en.wikipedia.org/wiki/Recycling